The ATS Thermal Bypass Valve O-Ring Kit is a 4-piece replacement seal set designed to restore leak-free performance on your transmission fluid cooler lines. Over time, heat cycles, maintenance, or overtightening threaded fittings can cause factory or aftermarket O-rings to degrade, leading to automatic transmission fluid (ATF) leaks. This kit gives you the essential replacement seals needed to maintain proper fluid pressure and prevent costly transmission fluid loss on Dodge, Ram, and FCA vehicles.
This O-ring replacement kit is engineered for Dodge and Ram HD trucks equipped with the 6.7L Cummins diesel engine, including 2500, 3500, 4500, and 5500 models from 2010 through 2024. It provides an exact fit for lines connected to 68RFE and Aisin AS69RC automatic transmissions. Additionally, these O-rings fit various Chrysler, Dodge, Jeep, Fiat, Alfa Romeo, and Maserati vehicles that utilize threaded cooler line fittings.
If you observe automatic transmission fluid pooling or seeping near your thermal bypass valve or cooler line connections, a compromised O-ring is often the root cause. Disassembling lines during routine maintenance or installing upgrade kits can distort old seals. Whether servicing an existing unit or stocking up on spares for your ATS 2010-2012 Thermal Bypass Valve Upgrades, 2013-2018 Thermal Bypass Valve Upgrades, or 2019-2024 Thermal Bypass Valve Upgrades, replacing them with fresh O-rings ensures a tight, reliable seal every time.
ATS Transmission packages carry a standard THREE YEAR Warranty. There are several exceptions, so refer to the Warranty’s specific terms and conditions . All labor, shipping, or any other charges associated with the product and the product’s failure are not covered under Warranty. Labor and/or shipping charges will not be refunded under any circumstance. After the one-year anniversary date of the original purchase, there is a limited parts replacement Warranty only. Transmissions that are purchased separately outside of a transmission package / stage and are installed without an ATS torque converter carry a 1 year parts only warranty and there is no labor or shipping allowance for transmission only purchases.
In the event of a product failure, the consumer must return the defective product to ATS for inspection before a replacement is sent to the consumer. After ATS inspects the product and completes the failure analysis, the inspection officer at ATS will provide written documentation stating the condition of the product and determine, to the best of his or her ability, what caused the malfunction or complaint. Based on the findings of the inspection report, ATS will determine whether there is a valid Warranty claim. Should a consumer require immediate service, and chooses not to wait for their product to be returned to ATS for inspection, service, and potential repair or replacement, the consumer can purchase a replacement product from ATS. The consumer must pay the full current MSRP, the applicable core charge, and shipping to and from ATS’ shop. When the defective product arrives, ATS will refund the core charge and inspect the product. During inspection, ATS will assess the product for warrantable damage. If the original product has indeed failed under the terms of the original Warranty, ATS will refund the full purchase price for the replacement product only. If the product has failed due to any issue not covered under the original Warranty, ATS will assess charges to the consumer based on any parts necessary to return the product to nominal ATS standards. ATS will deduct the total cost of required parts from the replacement product’s purchase price, and the consumer will be refunded the difference (if any) between the purchase price paid for the replacement product and the cost of parts.
If the consumer can wait for their product to be returned to ATS for inspection, service, and potential repair or replacement, the consumer pays shipping to and from ATS’ shop. When the defective product arrives in Colorado, ATS will inspect the product. ATS will then assess the product for warrantable damage. If the product has failed under the terms of the original Warranty contract, ATS will repair or replace the product – at ATS’s discretion. If the product has failed due to any issue not covered under the original Warranty, ATS will assess charges to the consumer based on any parts necessary to return the product to nominal ATS standards. ATS will bill the consumer for the total cost of parts required for repair of the product, and shipping to and from Colorado, prior to the repaired/replaced product being sent to the consumer.
This section incorporates Section 2, entitled “In the Event of a Failure.” ATS manual transmissions carry a 1-year/12,000 mile Warranty. ATS will not pay for any fluids replaced in the event of a transmission failure. There is no labor or freight warranty coverage on standard transmissions. Manual transmission shafts and gears are not covered by this Warranty on any transmission due to the capability of certain situations to cause stress-loads beyond the structural ability of the shaft or gear.
